Spare Parts

Centrifugal clutch with inbuilt 5mm keyway.

To suit 5.5HP & 6.5HP engines.

Bore 19.05mm (3/4 inch). 10 tooth, 420 pitch.

To suit engines for Sportz, Honda, Caged Drifta Go Karts.

Price: $65.00

Clutch Spring

To suit centrifugal clutch as pictured above.

Price: $8.00

Throttle cable for Drifta Go Karts.

This is suitable for use as an accelerator cable or a manual disc brake cable.

Extra long cable.

2.35 Metre length

Replacement part for our single seater Drifta Go Karts.

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Drift II Go Karts, Drift Trikes, Trolley's.

Ideal for any DIY building project. Ideal if you are modifying your kart, home-built karts or other projects.

Price: $14.00

8cm distance between 3 stud holes which are 10mm.

Inside diameter is 25mm with splines.

These are compatible with our Rear Axles 880mm & 980mm with splines. OD of flange is 104mm. Height of Rear Wheel hub is 45mm 

Rear wheel hubs for Drifta Go Karts, Grass Karts, Drift Trikes , Trolley's or ideal for any DIY project. 

Price: $30.00

Front wheel hubs complete with bearing.

ID of bearing is 17mm.

80mm distance between 3 stud holes which are 10mm. These are compatible with our Front connecting arms with a 17mm shaft. OD of flange is 104mm. Height of Front Wheel Hub is 45mm 

Ideal for Drifta Go Karts, Grass Karts, Drift Trikes , Trolley's or ideal for any DIY project.

These are good quality one piece fittings.

Price: $35.00

Bearing to suit Front wheel hub (as shown above)

Code: 6003

ID of bearing is 17mm

OD of bearing is 34mm

Price: $12.00

To suit our Drifta single seater Go Kart Wheel Hubs

12 x 10mm bolts 25mm long

12 x flat washers

12 x spring washers

12 x locking nuts

Price: $19.90

To suit our Drifta single seater Go Kart Wheel Hubs

3 x 10mm bolts 25mm long

3 x flat washers

3 x spring washers

3 x locking nuts

Price: $5.90

Front Connecting Arm/ Front Stub Axle/ Front Spindle for our single seater Drifta Go Karts (excluding Junior Drifta 80cc Go Kart).

Ideal for any DIY building project.

Compatible with our Front wheel hubs & tie rods. Shaft length 72mm Shaft diameter 17mm

Please note: The left side is the Left hand side when sitting in the drivers seat.

Price: $32.00

Front Connecting Arm/ Front Stub Axle/ Front Spindle for our single seater Drifta Go Karts (excluding Junior Drifta 80cc Go Kart).

Ideal for any DIY building project.

Compatible with our Front wheel hubs & tie rods. Shaft length 72mm Shaft diameter 17mm

Please note: The right side is the Right hand side when sitting in the drivers seat.

Please note Castle/Axle nuts are sold separately as a pair.

Price: $32.00

High quality stainless steel plate which is 2.5mm thick.

OD is 180mm. ID of centre hole is 38mm.

Brake Plate for Drifta Go Karts, Grass Karts, Drift Trikes , Trolley's or Ideal for any DIY project.

Compatible with our Right Hub Brake & Rear Axles.

Price: $32.00

Brake Disc Plate complete with Right Hub.

High quality stainless steel plate which is 2.5mm thick.

OD is 180mm.

ID of centre hole of Brake Plate is 38mm.

Comes complete with bolts.

To suit our Drifta Go Karts, Grass Karts, Drift Trikes , Trolley's.

Ideal for any DIY project. Compatible with our Rear Axles.

Price: $60.00

25mm distance between 6 bolt holes which are 5mm.

Inside diameter is 25mm with splines.

These are compatible with our Rear Axles 880mm & 980mm with splines.

OD of flange is 60mm. Height of Right Hub Brake is 45mm.

Right Hub Brake for Drifta Go Karts, Grass Karts, Drift Trikes , Trolley's or ideal for any DIY project.

Compatible with our brake plate.  

Price: $30.00

REAR DISC BRAKE ASSEMBLY

Cable operated caliper comes complete with brake pads.

Mechanical cable brake.
Suitable for 2.5-3mm brake disc plate.

Distance between mounting bracket holes centre to centre is 52mm.

Suitable for Grass Karts, Sliders, Carts, Drift Trikes, Trolley's or ideal for any DIY project.

Price: $30.00

To suit REAR DISC BRAKE ASSEMBLY.

(Mechanical cable brake system).

Rear Disc Brake Assembly pictured above.

Please note: Some brake pads for this brake assembly are rectangular shape. Please specify when ordering if you need the rectangular pads.

Price: $8.00

To suit smaller Go Kart Hydraulic brake units. (Not Xtreme Hydraulic brake units)

(Please note: this smaller  unit is now obsolete)

 Please note: Go Kart frames starting with serial # ZJLH had this smaller brake unit.

Price: $12.00

Standard Hydraulic Brake Assembly complete with caliper, hose & brake lever.

To suit butterfly steering wheels on Drifta Go Karts.

Brake hose length 140cm from caliper to handle. Comes complete with Hydraulic Brake Pads. (Code on Brake Pads YL-F328)

Easy to install, Just bolt on.

Compatible with our 2.5-3mm Brake Disc Plate
Please note: This brake unit is compatible with our Drifta Go Kart frames starting with LAKS.

Suitable for Drifta Go Karts, Grass Karts, Off Road Karts, Drift ll Go Karts, Sliders, Carts, Drift Trikes, Trolley's or ideal for any DIY project.

Please note: These units come complete and the master cylinder & handle reservoir cannot be sold separately.

Price: $69.00

HYDRAULIC BRAKE PADS (SET OF 2)
To suit Standard Hydraulic Brake Unit Complete With Hand Lever (pictured above) and Go Kart frames starting with serial # LAKS.

(Code YL-F328)

Price: $12.00

Available in different colours of go karts.

To suit Standard Hydraulic Brake Unit Complete with Hand Lever - LAKS serial.

Mounting holes are 40mm apart, holes drilled to suit brake caliper above.

Price: $20.00

XTREME HYDRAULIC BRAKE UNIT COMPLETE WITH HAND LEVER
Suitable for 2.5-3mm brake disc plate.
Brake hose length 160cm from caliper to handle.
To suit brake units for Go Kart frames starting with serial # ZJLH. (These are not the standard unit for our Drifta Go Karts with serial # LAKS... They can be used if adapted with a replacement brake bracket.)

For ZJLH... or LW-GK Drift Go Karts 2013 or older you will need a brake bracket to attach these brake units.( The original brake units on these karts are now obsolete)

These Xtreme Brake Units are ideal if you are building your own kart.

Suitable for Drift Go Karts, Grass Karts, Off Road Karts, Sliders, Carts, Drift Trikes, Trolley's or ideal for any DIY project.

Please note: These units come complete and the master cylinder & handle reservoir cannot be sold separately.

Comes complete with Xtreme Hydraulic Brake Pads

These brake pad codes below will fit this brake unit:

Code TL-F305

Code RH-7067

Code WF-021

Price: $75.00

XTREME HYDRAULIC BRAKE UNIT COMPLETE SUITABLE FOR FOOT PEDAL

These are designed for use with Foot pedals.

Brake hose length 125cm from caliper to handle.

Comes complete with Xtreme Hydraulic Brake Pads

(Code TL-F305) or (RH-7067) or (WF-021)

Compatible with our 2.5-3mm Brake Disc Plate

Please note: These units come complete and the master cylinder & handle reservoir cannot be sold separately.

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Go Carts, Drift Trikes,Trolley's or Ideal for any DIY building project. Ideal if you are modifying your kart, home-built karts or other projects.

Price: $95.00

XTREME HYDRAULIC BRAKE PADS (2PCS)  1 x SET
To suit Xtreme Hydraulic Brake Units (hand lever or foot units)

Code on brake pads can be:

TL-F305

RH-7067

WF-021 

Price: $15.00

Use this to mount Xtreme Brake Units to chassis.

PCD 65mm

Price: $10.00

190mm Length

Compatible with Xtreme Hydraulic Foot Brake Unit.

Ideal for any DIY building project. Ideal if you are modifying your kart, home-built karts or other projects.

Price: $22.00

AXLE BEARING (each)

UC 205

Inside diameter(ID) 25mm

Outside diameter (OD) 50mm

Comes with grub screws.

Compatible for use with our Rear Axle Shaft 880mm & 980mm

Ideal for any DIY project and suitable for 25mm axle.

Price: $18.00

30mm thick in centre tapering to 25mm at end with spline.

Length: 880mm

Compatible with our own Drifta brand Go Karts (serial # LAKS)

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Go Carts, Drift II Go Karts, Drift Trikes,Trolley's.

Ideal for any DIY building project. Ideal if you are modifying your kart, home-built karts or other projects.

Price: $85.00

30mm thick in centre tapering to 25mm at end with spline.

Length: 980mm 

Extra Long Rear Axle

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Go Carts, Drift II Go Karts, Drift Trikes,Trolley's or Ideal for any DIY building project. Ideal if you are modifying your kart, home-built karts or other projects.

Price: $90.00

This Rear Axle Kit includes 1 x 880mm Axle, 2 x Rear Hubs, 1 x Brake Plate, 1 x Brake Hub, 1 x Chain Drive Sprocket, 1 x Chain Hub, 2 x Axle Bearings, 2 x Axle Spacer-Short, 2 x Castle Nuts.

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Go Carts, Drift II Go Karts, Drift Trikes,Trolley's  

Ideal for building/modifying your own Go Kart or any DIY project.

Price: $290.00

This Rear Axle Kit includes 1 x 980mm Axle, 2 x Rear Hubs, 1 x Brake Plate, 1 x Brake Hub, 1 x Chain Drive Sprocket, 1 x Chain Hub, 2 x Axle Bearings, 2 x Castle Nuts, 2 x Spacers

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Go Carts, Drift II Go Karts, Drift Trikes, Trolley's. 

Ideal for building/modifying your own Go Kart or any other DIY project.

Price: $295.00

To suit 25mm Axle, these are sold as a pair.

ID: 25mm

OD: 32mm

Width is 20mm.

Price: $8.00

To suit 25mm Axle, these are sold as a pair.

ID: 25mm

OD: 37mm

Width is 50mm.

Price: $12.00

Axle Nuts suitable for Rear Axle and Front Connecting arms ( ID:15mm).

Sold as a pair.

To suit our Drifta Go Karts.

Ideal for any DIY building project.

Ideal if you are modifying your kart, home-built karts or other projects.

Price: $2.50

Bearing bracket/holder available in different colours of go karts.

Inside diameter: 50mm

Distance between 3 bolt holes is 65mm.

Compatible with our Drifta brand Go Karts (serial # LAK) and components.

Ideal for DIY Drift Go Karts, Buggies, Trolleys.

Ideal if you are modifying your kart, home-built karts or other projects.

Price: $10.00

Chain 31 link 

420 drive chain 80cm length

To suit Go Kart frames with a 6.5HP Engine with centrifugal clutch starting with serial # LAKS

(Sportz Drifta 200cc, Caged Drifta 200cc, Honda Drifta 163cc)

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Drift II Go Karts, Drift Trikes, Trolley's.

Ideal for any DIY building project.

Ideal if you are modifying your kart, home-built karts or other projects.

Price: $23.00

Chain 30 link

To suit Go Kart frames starting with serial # ZJLH.

Price: $22.00

Chain 36 link

420 drive chain

To suit Go Kart frames with a 6.5HP Engine with wet clutch, serial # LAKS.

Compatible with Trail Blazer, Blazer & Ultimate Drifta Go Karts.

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Drift II Go Karts, Drift Trikes, Trolley's.

Ideal for any DIY building project.

Ideal if you are modifying your kart, home-built karts or other projects.

Price: $24.00

Left Hub Chain for our Drifta single seater Go Karts.

(excluding Junior Drifta 80cc Go Karts).

Compatible with our Chain Drive Sprocket & Rear Axles. High quality stainless steel which is 6mm thick.

Outside Diameter is 95mm Height is 45mm. ID of centre bore is 25mm with spline.

4- hole stud pattern with distance between centre of holes 57mm. 10mm holes.

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Drift II Go Karts, Drift Trikes, Trolley's.

Ideal for any DIY building project. Ideal if you are modifying your kart, home-built karts or other projects.

Price: $30.00

48 tooth 420 rear sprocket 

Chain Sprocket for Drifta Go Karts, Grass Karts, Off Road Go Karts, Drift ll Go Karts, Drift Trikes ,Trolley's.

Ideal for any DIY building project.

Compatible with our Left Hub Chain & Rear Axles. High quality stainless steel which is 6mm thick. Outside Diameter tip to tip is 198mm.

ID of centre bore is 52mm.4 hole stud pattern with distance between centre of holes 57mm.

Price: $32.00

54 tooth 420 rear sprocket 

Chain Sprocket for Drifta Go Karts, Grass Karts,Off Road Go Karts, Drift ll Go Karts, Drift Trikes ,Trolley's.

Ideal for any DIY building project.

Compatible with our Left Hub Chain & Rear Axles. High quality stainless steel which is 6mm thick. Outside Diameter tip to tip is  220mm. ID of centre bore is 52mm.4 hole stud pattern with distance between centre of holes 57mm.

Price: $38.00

48 tooth 420 rear sprocket 

Chain Sprocket complete with Left Hub Chain for Drifta Go Karts, Grass Karts,Off Road Go Karts, Drift ll Go Karts, Drift Trikes ,Trolley's.

Ideal for any DIY building project.

Compatible with our Rear Axles and chains. Chain drive sprocket is high quality stainless steel which is 6mm thick. Outside Diameter tip to tip is 198mm.

ID of centre bore is 52mm.4 hole stud pattern with distance between centre of holes 57mm.

Come complete with bolts, nuts and washers.

Price: $60.00

To suit Sportz, Caged, and Honda Drifta Go Karts with dry centrifugal clutch engine.

Easy to bolt on.

Price: $30.00

To suit Trail Blazer, Blazer, and Ultimate Drifta Go Karts with wet clutch engine.

Easy to bolt on.

Price: $30.00

Total length: 210mm

Eye to eye: 180mm 

To suit our own Drifta Go Kart frames starting with serial # LAKS.

Ideal for any DIY building project.

Ideal if you are modifying your kart, home-built karts, trolley's or other DIY projects.

Price: $28.00

Total length: 210mm.

Eye to eye: 180mm
To suit Go Kart frames starting with serial # ZJLH.

Ideal for any DIY building project.

Ideal if you are modifying your kart, home-built karts, trolley's or other DIY projects.

Price: $28.00

Replacement air filter for 5.5 & 6.5HP Honda or Honda design engines. 

Suitable for 4-stroke petrol engines with a horizontal shaft.

To suit our Drifta single seater Go Kart engines.

Price: $18.00

This is the complete air filter assembly.

Includes air filter and plastic casing.

This will fit most 5.5 & 6.5HP petrol engines. The bolt holes are approximately 44mm apart.

Price: $38.00

KILL SWITCH on/off

Compatible with KILL SWITCH WIRING (below).

Attaches to Steering Wheel (Butterfly style) on Drifta Go Karts.

A good safety feature with KILL SWITCH WIRING to add to any motorised product.

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Drift II Go Karts, Drift Trikes, Trolley's.

Ideal for any DIY building project. Ideal if you are modifying your kart, home-built karts or other projects.

Price: $10.00

KILL SWITCH WIRING to attach to KILL SWITCH on/off

Length of wiring is 170cm

Attaches to wiring on engine.

A good safety feature with KILL SWITCH on/off to add to any motorised product.

Compatible with Drifta Go Karts

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Drift II Go Karts, Drift Trikes, Trolley's.

Ideal for any DIY building project. Ideal if you are modifying your kart, home-built karts or other projects.

Price: $15.00

Throttle/ Accelerator handle.

Attaches to our Steering wheel - Drifta (Butterfly style)

Used as a throttle lever for our Drifta brand karts with hand controls.

Can be used with a cable for mechanical brake system (Rear Disc Brake Assembly).

Please note: This is not a handle for  our Hydraulic brake units.

Price: $18.00

Butterfly Style or Formula One Steering Wheel.

340mm Across x 170mm Height

Distance between 3 mounting holes to attach to steering shaft is 33mm.

Compatible with our Drifta brand single seater Go Karts (excluding Junior Drifta 80cc Go Kart).

Attaches to Steering Column.

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Go Carts, Drift Trikes,Trolley's or Ideal for any DIY building project. Ideal if you are modifying your kart, home-built karts or other projects.

Price: $39.00

310mm Width x 260mm Height.

Distance between 6 bolt holes to attach to steering shaft/column is 35mm

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Go Carts, Drift Trikes,Trolley's or Ideal for any DIY building project. Ideal if you are modifying your kart, home-built karts or other projects.

Price: $49.00

 Includes steering wheel, steering column with fittings and kill switch.

Compatible with all our Drifta single seater Go Karts (excluding Junior Drifta 80cc Go Kart).

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Go Carts, Drift Trikes,Trolley's or Ideal for any DIY building project. Ideal if you are modifying your kart, home-built karts or other projects.

Price: $95.00

Steering column 540mm long.

Distance between 3 mounting holes to attach to steering wheel is 33mm.

Compatible with our Steering Wheel (Butterfly style) for our own Drifta brand karts.

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Go Carts, Drift Trikes,Trolley's or Ideal for any DIY building project. Ideal if you are modifying your kart, home-built karts or other projects.

Price: $37.00

Steering column with fittings 540mm long.

Includes bottom plate.

Distance between 3 mounting holes to attach to steering wheel is 33mm.

Compatible with our Steering Wheel (Butterfly style) for our own Drifta brand karts

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Go Carts, Drift Trikes,Trolley's or Ideal for any DIY building project. Ideal if you are modifying your kart, home-built karts or other projects.

Price: $57.00

92mm length.

Attach to steering tie rod from steering column.

Price: $8.00

This Accelerator Plate / Throttle Lever is suitable for 5.5HP & 6.5HP engines.

Replacement part for our Drifta single seater Go Karts.

The plate/lever is compatible for attaching Throttle cable to engine on Go Karts or Grass Karts.

Price: $22.00

Ignition system/Coil for 5.5HP & 6.5HP petrol engines (Transitorized magneto).

Price: $49.00

Spark plug cap for 5.5 & 6.5HP petrol engines.

Price: $9.90

DUST CAP for Drifta Go Kart wheels hubs.

Price: $5.00

Go Kart Seat

440mm Across x 430mm Height

Compatible with all our Drifta single seater Go Karts excluding Junior Drifta 80cc.

Heavy Duty Strong Flexible Plastic.

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Go Carts, Drift II Go Karts, Drift Trikes,Trolley's or Ideal for any DIY building project. Ideal if you are modifying your kart, home-built karts or other projects.

Price: $50.00

Seat Cover Vinyl.

To suit our Drifta single seater go kart seats (excluding Junior Drifta 80cc).

630mm across (line of fabric) Maximum width.

Price: $20.00

Seat cover padded with blue stripes.

To suit Go Kart Seat pictured above.

Price: $48.00

Color: blue

Seat cover padded with red stripes.

To suit Go Kart Seat pictured above.

Price: $48.00

Color: red

Lap belt.

2 bolting points

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Go Carts, Drift II Go Karts, Drift Trikes,Trolley's or Ideal for any DIY building project.

Ideal if you are modifying your kart, home-built karts or other projects.

Price: $24.00

Harness 3 point seat belt.

These suit our Drifta brand single seater Go Karts (excluding Junior Drifta 80cc).

Easy adjustable straps to suit all sizes. 3 bolting points.

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Drift II Go Karts, Drift Trikes,Trolley's.

Ideal for any DIY building project. Ideal if you are modifying your kart, home-built karts or other projects.

Price: $45.00

Long tie rod/Steering rack with ball/rose end joints.

These suit our Drifta single seater Go Karts (excluding Junior Drifta 80cc).

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Drift II Go Karts, Drift Trikes,Trolley's.

Ideal for any DIY building project. Ideal if you are modifying your kart, home-built karts or other projects.

These measure 615mm eye to eye.

Price: $30.00

Short tie rod/Steering rack with ball/rose end joints.

These suit our Drifta brand single seater Go Karts (excluding Junior Drifta 80cc).

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Drift II Go Karts, Drift Trikes, Trolley's.

Ideal for any DIY building project. Ideal if you are modifying your kart, home-built karts or other projects.

These measure 310 mm eye to eye.

Price: $25.00

FRONT FRAME FOR DRIFTA GO KARTS 
Suitable for Sportz Drifta, Honda Drifta, Trail Blazer and Blazer Drifta Go Karts (non-caged karts).

Please note: These frames suit our own brand Drifta Go Karts.
Please specify the serial # on your Go Kart when ordering this part. (LAKS (our Drifta Karts) or ZJLH)
Available in most kart colours, please specify your colour preference when ordering or Enquire if we have in stock.

Price: $85.00

Color: all colours available

FRONT FRAME FOR CAGED DRIFTA GO KARTS

Suitable for Caged Drifta and Ultimate Drifta Go Karts.

Please note: These frames suit our own Drifta Go Karts.
Please specify the serial # on your Go Kart when ordering this part. (LAKS (our Drifta Karts) ZJLH, LWGK) 
Available in most kart colours, please specify your colour preference when ordering or Enquire if we have in stock.

Our roll cages attach to this front frame.

Price: $90.00

Color: all colours available

These are suitable for bolting front frame to mid frame.

Sold as a pair.

ID: 15mm 

Price: $2.50

Attaches behind seat to main frame.

Price: $40.00

Complete Roll Cage.

Includes padding for bars ,and black fabric sun cover (not shown in photo).

Includes built-in comfortable padded head rest.

Comes as a kitset, just need to be bolted together.

These suit our Drifta brand single seater Go Karts (excluding Junior Drifta 80cc).
Suitable for Go Karts, Grass Karts, Off Road Go Karts, Drift II Go Karts, Drift Trikes, Trolley's.

Ideal for any DIY building project. Ideal if you are modifying your kart, home-built karts or other projects.

Price: $215.00

Color: Black

Rear frame for our Drifta single seater Go Karts.

Also suitable for other DIY projects including Drift Trikes.

If this is for one of our Drifta Go Karts please advise which model as the engine mounting differs.

Centrifugal Dry Clutch 6.5HP Engine 

Wet Clutch 6.5HP Engine 

Wet Clutch 9.0 HP Engine

Please specify colour preference when ordering.

We cannot guarantee colour choice.

Price: $125.00

Color: black,red,blue

To suit swing arm on Rear Frame. (pictured above).

38mm Length

10mm Centre hole

Price: $9.90

OUT OF STOCK

The most widely used, Honda design chinese engine.

Used to power Go Karts, Grass Karts, homebuilt karts and trolley's.

New design and built strong to last.

• 6.5 HP(5Kw) Engine 200cc centrifugal dry clutch with 19mm shaft
• 4-stroke air cooled
• Recoil pull start
• Comes complete with centrifugal clutch which has 10 tooth sprocket
• Suitable for a 420 sprocket & 420 chain
• Engine manual & spark plug remover included
• GW: 14.5kg

Replacement engine for our Sportz, Caged, Honda Drifta Go Karts.

Price: $369.00

The most widely used, Honda design chinese engine.

Used to power Go Karts, Grass Karts, homebuilt karts and trolley's.

New design and built strong to last.

• 6.5 HP(5Kw) Engine 200cc WET CLUTCH with 2:1 Reduction gear box.
• 4-stroke air cooled
• Recoil pull start
• Comes complete with clutch & 14 tooth drive sprocket as pictured below
• Engine manual & spark plug remover
• GW: 19kg

Replacement engine for our Trail Blazer, Blazer, Ultimate Drifta Go Karts.

Price: $425.00

To suit 6.5HP engine with a Centrifugal dry clutch.

Price: $3.90

To suit 6.5HP engine with a wet clutch.

Price: $3.90

To suit 5.5 and 6.5HP engines.

Price: $8.00

To suit 6.5HP Motor 200cc with wet clutch.

2:1 Reduction gear box.

Price: $105.00

To suit 6.5HP Motor 200cc Wet Clutch.

420 PITCH.

Price: $15.00

To suit 6.5HP Motor 200cc Wet Clutch.

14 Tooth sprocket

With key, spacer, washer, and bolt for engine shaft

420 PITCH

Price: $19.90

Exhaust muffler

To suit 5.5HP & 6.5HP engines.

Price: $32.00

Recoil Pull Start assembly.

To suit 5.5HP & 6.5HP stationary engines.

Measures 175mm diameter. Mounting bolt holes at 160mm PCD.

To suit engines on our Drifta single seater Go Karts (excluding Junior Drifta Go Kart).

Price: $30.00

Fuel Cap

To suit 5.5HP, 6.5HP engines.

Price: $10.00

To suit 5.5HP, 6.5HP engines.

Fuel tank capacity: 3.6L

Price: $50.00

Carburetor for 6.5HP engine.

Throat size 19mm & 42mm centres for mounting bracket.

To suit engines on our Drifta single seater Go Karts (excluding Junior Drifta Go Kart).

Price: $55.00

NGK Spark plug BPR5ES

Price: $9.95

80cc 4-STROKE ENGINE with recoil pull start

To suit our Junior Drifta 80cc Go Karts

1.2 litre fuel tank

3.5HP

Air cooled

Complete with Centrifugal Clutch

Price: $379.00

To suit our Xtreme Drifta 270cc Go Karts

9.0 HP stationary petrol engine

Delivers strong power and torque

Measurements of engine: 

Length 420mm

Width 300mm

Height 420mm

Shaft diameter 25mm

Shaft length 64mm

Product features:

• Complete with wet clutch
• Air cooled, 4-stroke OHV
• Recoil pull start
• 6 litre tank
• Bore & Stroke 77 & 58mm
• Displacement 270cc
• Max power 6.6kw at 3600rpm
• 1.1 litre oil capacity

GW: 31kg NW: 29kg

Price: $695.00

Genuine Honda Engine GX160

Air cooled 4-stroke OHV

Recoil Pull start

Complete with Clutch

Bore & Stroke 68 & 54mm

Price: $649.00

OUT OF STOCK

Genuine Honda Engine GX200

Air cooled 4-stroke OHV

Recoil Pull start

Complete with Clutch

Bore & Stroke 68 & 54mm

Price: $695.00

WHEEL RIM DRIFT Go Kart 13*5-6

172mm Diameter x 98mm Width

Bolt hole diameter 10mm

To suit  tyres 13*5-6 

(Our Sportz, Trail Blazer, Caged, and Honda Drifta Go Karts )

Price: $25.00

WHEEL RIM DRIFT Go Kart 145/70-6

172mm Diameter x 114mm Width

To suit tyres 145/70-6 

(Our Blazer, Ultimate and Xtreme Drifta Go Karts)                                                                                             

Price: $28.00

WHEEL RIM DRIFT Go Kart 7" 

200mm Diameter x 132mm Width

To suit 15*5-7 and 16*8-7 tyres.

Price: $30.00

Size 13*5-6.

Inflated 290mm Diameter x 120mm Wide.

Tubeless

To suit WHEEL RIM DRIFT Go Kart 172mm Diameter x 98mm Width

These tyres will fit our Sportz, Caged, Honda, Junior, and Trail Blazer Drifta Go Karts.

Suitable for Drifta Go Karts, Grass Karts, Off Road Karts, Drift ll Go Karts, Sliders, Carts, Drift Trikes, Trolley's or ideal for any DIY project.

Price: $28.00

BUY 2 FOR DISCOUNT. 13*5-6.

Inflated 290mm Diameter x 120mm wide.

Tubeless.

To suit WHEEL RIM DRIFT  Go Kart 13*5-6 172mm Diameter x 98mm Width.

These tyres will fit our Sportz, Caged, Honda, Junior, and Trail Blazer Drifta Go Karts.

Suitable for Drifta Go Karts, Grass Karts, Off Road Karts, Drift ll Go Karts, Sliders, Carts, Drift Trikes, Trolley's or ideal for any DIY project.

Price: $50.00

Slick tyre 13*5-6.

Inflated 290mm Diameter x 120mm Wide.

Tubeless.

To suit WHEEL RIM DRIFT Go Kart 13*5-6 172mm Diameter x 98mm Width.

These tyres will fit our Sportz, Caged, Honda, and Trail Blazer Drifta Go Karts.

Suitable for Drifta Go Karts, Grass Karts, Off Road Karts, Drift ll Go Karts, Sliders, Carts, Drift Trikes, Trolley's or ideal for any DIY project.

Awesome for etxra sliding & drifting on grass.

Price: $32.00

BUY 2 FOR DISCOUNT 13*5-6

Inflated 290mm Diameter x 120mm Wide.

Tubeless.

To suit WHEEL RIM DRIFT Go Kart 13*5-6 172mm Diameter x 98mm Width.

These tyres will fit our Sportz, Caged, Honda, and Trail Blazer Drifta Go Karts.

Suitable for Drifta Go Karts, Grass Karts, Off Road Karts, Drift ll Go Karts, Sliders, Carts, Drift Trikes, Trolley's or ideal for any DIY project.

Awesome for etxra sliding & drifting on grass.

Price: $60.00

Tyre size 145/70-6

Inflated 355mm Diameter x 135mm Wide.

Tubeless

To suit WHEEL RIM DRIFT Go Kart 145/70-6

Please note: Tread pattern may vary slightly to image shown.

Suitable for Drifta Go Karts, Grass Karts, Off Road Karts, Drift ll Go Karts, Sliders, Carts, Drift Trikes, Trolley's or ideal for any DIY project.

Price: $38.00

BUY 2 FOR DISCOUNT

Tyre size 145/70-6

Inflated 355mm Diameter x 135mm Wide.

Tubeless

To suit WHEEL RIM DRIFT Go Kart 145/70-6

Please note: Tread pattern may vary slightly to image shown.

Suitable for Drifta Go Karts, Grass Karts, Off Road Karts, Drift ll Go Karts, Sliders, Drift Trikes, Trolley's.

Ideal for any DIY project.

Price: $70.00

Knobbly, Slick or Road tyres Size: 13*5-6

Please specify when ordering which tread type you require.

KNOBBLY, SLICK (smooth), or ROAD

Please note: Slick tread type is in main illustration.

Price: $45.00

BUY 2 FOR DISCOUNT.

Knobbly, Slick or Road tyres 13*5-6. 

Please specify when ordering which tread type you require.

KNOBBLY, SLICK, ROAD

Please Note: Road tread type is illustrated.

Price: $85.00

BUY 4 FOR DISCOUNT.

Knobbly, Slick or Road tyres 13*5-6. 

Please specify when ordering which tread type you require.

KNOBBLY, SLICK(smooth), ROAD

Please note: Knobbly tread type is in main illustration.

Price: $160.00

Tyre size 145/70-6.

Tubeless.

To suit our Blazer, Ultimate & Xtreme Drifta Go Karts.

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Go Carts, Drift II Go Karts, Drift Trikes,Trolley's.

Ideal for any DIY building project. Ideal if you are modifying your kart, home-built karts or other projects.

Please note: Tread pattern may vary slightly to image shown.

Price: $55.00

BUY 2 TO GET DISCOUNT.

Tyre size 145/70-6.

Tubeless.

To suit our Blazer, Ultimate & Xtreme Drifta Go Karts.

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Go Carts, Drift II Go Karts, Drift Trikes,Trolley's.

Ideal for any DIY building project. Ideal if you are modifying your kart, home-built karts or other projects.

Please note: Tread pattern may vary slightly to image shown.

Price: $100.00

Tyre size 16*8-7.

Inflated 410mm Diameter x 165mm wide. Tubeless.

Compatible with WHEEL RIM DRIFT Go Kart 7 inch.

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Go Carts, Drift II Go Karts, Drift Trikes,Trolley's.

Ideal for any DIY building project.

Ideal if you are modifying your kart, home-built karts or other projects.

Price: $50.00

Tyre size 16*8-7

Tubeless.

Please Note: Tread pattern may vary to image shown. 

Rim colour is silver. 

Price: $75.00

Drifta go kart chassis.

Ideal for DIY projects. 

Price: $995.00